Thingsee ENVIRONMENT installation instructions
Using Thingsee ENVIRONMENT sensor
Indoor environment monitoring can make any building or space smart. Real-time information over temperature and humidity can be used to create better end-user experiences, efficient energy consumption and better facility management planning with factual data over the environmental factors.
Thingsee ENVIRONMENT sensor measures temperature, humidity, barometric pressure, and ambient light. In addition, it has an accelerometer and a magnetic switch.
Thingsee ENVIRONMENT’s magnetic switch recognition can be used to monitor the open/closed position of doors and windows, and the ambient light sensor can recognize if the lights are on or off.
The accelerometer can identify the sensor’s position, but also recognise even the smallest G-forces, which can be used to measure machine usage rates. This is very handy when tracking the usage for various machines and predicting their maintenance needs.
The sensor is for indoor use only. The environment humidity can be measured between 0 - 100 % RH at all time. The usage temperature range is -40 ºC to +85 ºC, non-condensing environments only.
Note before installation
Please make sure the Thingsee gateway device is installed before you install the sensor.
To ensure strong enough signal strength for data delivery, keep the maximum distance between installed sensors under 20 m.
If the distance between a measuring sensor and the gateway is > 20 m or if the sensors are separated by a fire door or other thick building materials, use extra sensors as routers to ensure adequate signal strength.
Things to avoid in installation
Avoid installing the Thingsee products near the following:
- Thick concrete structures or thick fire doors
- Electrical transformers or thick electrical wires
- Nearby heating or cooling devices and/or vents
- Direct sun light
- Nearby halogen lamps, fluorescent lamps or similar lamps with hot surface
- Nearby radio equipment like WiFi routers or any other similar high power RF transmitters
- Inside metal box or covered with a metal plate
- Inside or underneath a metal cabinet or box
- Near elevator motors or similar targets causing a strong magnetic field
- Avoid installing the sensor in close proximity to a spot where there’s people presence constantly, such as right next to workstations
Please make sure the Thingsee gateway device is installed before you install the sensors. To identify the sensor, read the QR code on the front of the device with a QR code reader or Thingsee installation application on your mobile device. Identifying the device is not necessary, but it will help you keep track of your IoT installation and help Haltian support to solve possible issues.
Note: Make sure the sensor is installed max. 20 meters form the next sensor or gateway. This is to ensure full coverage mesh network between the sensors and the gateway.
Carefully pull out the battery security tab. LED indicator (red) will flash once. If the LED doesn’t flash within 2 minutes, tap the sensor against your palm. If you do not see the LED blink or see the events from the sensor within 5 minutes, re-install the batteries.
Clean the surface you will attach the sensor to with IPA -solvent (isopropyl alcohol). Remove the tape’s paper cover from the backside of the sensor.
Attach the sensor to its place by pushing it firmly against the surface for a minimum of 5 seconds.
Changing the batteries
Open the sensor to change the batteries or reboot the device by replacing the batteries.
To monitor temperature, humidity, air pressure and light levels, install the sensor on a wall at 1,2 m height.
Monitoring the open/closed position of door and windows
Thingsee ENVIRONMENT is used to monitor doors and windows with the magnet holder accessory. The magnet holder is attached to the door or window, and Thingsee ENVIRONMENT is attached to the frame, so that when the door/window is closed, the sensor detects the magnet by its side.
The small magnet inside the magnet holder accessory is positioned so that the magnet is aligned with the magnetic switch inside Thingsee ENVIRONMENT. The magnetic switch is on the left side of the device.
When the magnet holder comes across the sensor device, the magnet is placed in magnet position 1 (see image 1). When the holder and the sensor device are aligned, the magnet is placed in magnet position 2 (see image 2). Make sure to align the sensor and the magnet holder at the bottom.
Magnet position 1
Magnet position 2
Machine usage mode
Thingsee ENVIRONMENT’s accelerometer can detect the smallest of G-forces so it can be used to detect the vibration of small or big machines. The device is simply installed to where the vibration of the machine is felt when it’s turned on.